Alphatech Fermax PBX EXP Instalační příručka

Fermax PBX DP analogue door phone panel Fermax PBX EXP Fermax PBX KEY Fermax PBX CAM Fermax PBX EA User and installation

1.3 Characteristics of the modules 1.3.1 The basic module of electronics Fermax PBX DP The basic module of Fermax PBX DP panel is supplied

Picture 2 The real image of connection and set-up elements 1. Service jumper is used usually in case when the user forgets the service password f

3. Loudspeaker loudness SPK – you can set the desired loudspeaker loudness/volume with the trimmer. Attention – the louder the loudspeaker volume, th

or for 12V - 24VDC (direct), max. cnsumption is 250mA (+ 3,5mA x number of visit cards). 11. Switching contact of 2nd relay (NO=normally open, NC=nor

15. Connector 8 - for connecting 8 pushbuttons (integrated expansion). For connection please use an interconnection cable Fermax PBX CC8. Each colo

1.3.2 Example of switches connection The switching contact of relay is separated galvanically from other circuits of the door phone panel. Also 12V

can also find a red LED under the visit card – it is used for signallisation of the door phone panel status. 5. Microphone 1.3.4 Exchange of visit c

The numbering of positions is shown on the picture 5. All numbers of pushbuttons refer to the settings of the door phone panel (see more in the progr

1.4 Assembly of the door phone panel 1.4.1 Surface mounting For surface mounting we offer a compact installation box. The installation box is m

When installing the door phone panel in the environment where water may be condensing (temperature changes) or where it may be raining on the door ph

2 Door Phone NUDV (Fermax PBX DP) Operation 2.1 Signaling Overview The Door Phone NUDV (Fermax PBX DP) signals an acoustic conditions they may occur

guard will lift up the line neither immediately (the button is not the first number from code lock), or with delay (parameter 53) and after period gi

number is stored (same as for buttons). The number dialing is managed by Day/Night setting or mode for two groups of numbers (as described in Chapter

3 Programming of Parameters 3.1 Programming through Phone 3.1.1 Entry to Programming The New Door Phone NUDV will be set to programming mode in two

will be sufficient and the guard immediately responds by error tone, but he will extend the period to hanging up.. Note 2. The # sign is not used by

4 Description of Parameters 4.1 Direct Dialing – Memories Parameter Value Meaning Basic 1 tt nn… No. nn under button tt - tt – Button number (

m=3 lighting mode – it will close by guard lifting up and stay closed even for ss period after guard hanging up (the line is engaged for this perio

The same command can be set for both switches, then they are activated at the same time. The advantage is to set the same command both for switch clo

Parameter Value Meaning Basic 42 z sign for call extension * z – sign for call extension * or # (10sec before call end the guard will send a not

Parameter Value Meaning Basic 48 c keyboard connection 0 c – c=0 only NC-mode connected to the basic module c=1 the keyboard connected on t

Welcome Congratulations on purchasing the door phone panel “Fermax PBX Door Phone” Fermax PBX DP. This door phone can satisfy your need of com

Parameter Value Meaning Basic 52 d max. call time 2 d – max. time, for which the guard is hanging up, this time can be extended during call by sig

Parameter Value Meaning Basic 55 z time before dialing 1 z – time [sec] after guard lifting up before dialing [range 1-5]. This time is differen

4.5 Presetting and Deleting Parameter Value Meaning Basic 8# # basic setting executes This setting does not influence 1 and 2 (numbers stored in m

4.7 System Setting Parameter Value Meaning Basic 6# s number of non-fitted buttons of basic module The basic module is fitted with 2 buttons as sta

4.8 Overview of Parameters Parameter Value Meaning Basic 1 tt nn… No. nn under button tt - 2 tt nn… No. nn under button tt - 31 r m switch r works

57 t DTMF tone duration (tone) choice 5 (100ms) 58 m gap duration among DTMF tones 5 (100ms) 59 f Flash duration 1 (100ms) 50 p pause duration / int

4.9 List of Presetting Parameters parameter basic presettings switch 1 mode lock m=1 switch 2 mode lock m=1 passw.Day+Night switch 1 not passw.

5 Technical Parameters 5.1 Electrical Parameters Parameter Value Conditions Minimum line current 18mA line answered Minimum line voltage 18V line

6 Table for Easy Programming Complete the values in empty part of table you want to program. In double-frame part there are whole programming comman

Password for switch 1 Day+Night321 6 Password for switch 2 Day+Night322 6 Password for switch 1 Day 331 6 Password for switch 2 Day 332 6 Password f

Manual version V8.1 6. 4.2010 Contents 1 BASIC DESCRIPTION ...

Pause durat. / interdigit gap nx100 50ms 1

Guarantee conditions: The product was shop-checked. The producer guarantees that this product will keep the features described in these operating ins

© JR 2010 version V8.1 IV/10

4.8 OVERVIEW OF PARAMETERS ... 344.9 LIST OF PRESETTING PARAMETERS ...

1 Basic description 1.1 Features ¾ Modular system with 1 to 64 pushbuttons ¾ Two 16-digit numbers stored on each pushbutton ¾ It can be connected

1.2 Assembly of panels The building blocks of Fermax IP DP are the basic panels which differ by its size, number of pushbuttons, if the visit card h

1.2.2 Examples of panels Fermax PBX DP Fermax PBX DP Fermax PBX EA Fermax PBX KEY 1 AP 201 1 AP 101 1 A 1

Please do not use systems which do not support DTMF transmission during the call from the wireless DECT phone to the other wireless DECT phone (e.g.